ET1112
  • Rail mounting

  • Selectable dual-set value

  • Selectable PT100, J, K, L, T, S, R sensor types

  • Selectable 0-20mA, 4-20mA, 0-10V, 2-10V, 0-25mV and 0-50mV input

  • Programmable D1 and D2 digital contact input

  • PID control function with accurate self-tuning

  • Selftune for automatic PID calculation or manually enter PID parameters if known

  • Control outputs can be cancelled. (To use for measurement purposes)

  • Control outputs can be cancelled. (To use for measurement purposes)

  • Soft-Start function

  • Communication via RS-485 ModBus protocol

  • Programmable and firmware update via ModBus

  • Selectable analog, SSR or relay control output

  • C/A2 Relay output can be programmed as secondary alarm or control output

  • A1 relay output can be programmed as PID cooling or Primary alarm output

  • Selectable heating/cooling control

  • Offset feature for input

  • In the case of sensor failure, periodical running or relay state selection

  • Up to 7 slave devices can be connected simultaneously

  • Profile control up to 16 steps

  • On-demand relay output at profile steps

  • Timer and thermostat feature can be used in profile control mode

  • CE marked according to European Norms

Manuals

Environmental Conditions
Ambient/Storage Temperature0...50 ºC / -25...70 ºC
Relative Humidity80% relative humidity for temperatures up to 31 °C, decreasing linearly to 50% at 40 °C
Protection DegreeAccording to EN 60529 IP20
HeightMax. 2000m
Electrical Characteristics
Supply24V DC 20%
Power ConsumptionMax. 5VA
External ConnectionsPlug-in terminals
ScalePt-100 resistance thermometer -199.9...600.0 °C / -200...600 °C
J (Fe-CuNi) thermocouple -30.0....600.0 °C / -30....600 °C
K (NiCr-Ni) thermocouple -30.0...999.9 °C / -30...1300 °C
L (Fe-CuNi) thermocouple -30.0....600.0 °C / -30....600 °C
T (Cu-CuNi) thermocouple -30.0...400.0 °C / -30....400 °C
S (Pt10Rh-Pt) thermocouple -40...1700 °C
R (Pt13Rh-Pt) thermocouple -40...1700 °C
0-20mA, 4-20mA, 0-10V, 2-10V, 0-25mV, 0-50mV max. scale range 10000 (-10000...10000)
AccuracyResistance thermometer 0-20mA, 4-20mA, 0-10V, 2-10V, 0-25mV, 0-50mV: ±0.2% (of full scale) ± 1 digit
Thermocouples: ±0.5% (of full scale) ± 1 digit
Line ResistanceMax. 100ohm for thermocouple, max. 20ohm for 3-wired Pt-100
Outputs
C/A2 OutputRelay: 250V AC, 2A (for resistive load), NO or Alarm2 selectable as control or Alarm2 output
A1 OutputRelay: 250V AC, 2A (for resistive load), NO/NC selectable (Alarm1 output)
ANL/SSR Output0-20mA, 4-20mA, 0-10V, 2-10V analog SSR
Max. load resistance 600ohms for mA output and SSR mode. Source resistance 500ohms for V output
Life ExpectancyMechanical 10.000.000 operations (under no load), Electrical 300.000 operations (2A at 250V AC, resistive load)
Control
Control TypeSingle set-point and alarm control
Control AlgorithmOn-Off, P, PI, PD, PID (selectable)
A/D Converter14 bit
Sampling Time100ms
Proportional BandAdjustable between 0.0% and 100.0%. If Pb=0%, On-Off control is selected
Control PeriodAdjustable between 1 and 125s
HysteresisAdjustable between 1 and 50 °C/F
Output PowerThe ratio of power at a set point can be adjusted between 0% and 100%
Housing
Mounting MethodRail mounting
DimensionsG29xY90xD64 mm
WeightApprox. 200g (after packaging)
Enclosure MaterialSelf extinguishing plastics
Looks like you don't speak Turkish. Would you like to view this content in English? Yes, please No